ServicesEquipment Installation
Pool Equipment Installation in Chandler
We install pool pumps, filters, heaters, salt systems and automation at your home, sized to your pool and hooked up to code. You get a clear plan, an honest answer on whether a permit is needed, and equipment that runs quietly without tripping breakers.
New Equipment, Installed So It Passes and Lasts
Most pool equipment fails slowly. A pump starts to whine, a filter tank cracks after years of summer sun, or a heater stops lighting when the pool needs it most. When repair no longer makes sense, the replacement has to fit your plumbing, your electrical panel and the size of your pool. A pump that is too big wastes power and can strain the filter. One that is too small never turns the water over.
We are ROC licensed, and we treat the code side of an install as part of the job, not an afterthought. That means tying the new equipment into the existing bonding grid, protecting circuits the way the electrical code calls for, and telling you plainly when the city needs to issue a permit and inspect the work. If it does, we explain what the inspector will look at before we start, so nothing about inspection day is a surprise.
What We Install
Variable-speed pumps
Federal efficiency rules mean most replacement pool pumps are now variable speed. We set the speeds and run schedule for filtering, cleaning and any water features so you are not paying to run the motor flat out all day.
Cartridge, sand and DE filters
We match the filter to your pump's flow and your pool's volume. If you are switching filter types, we explain what changes in maintenance before you decide.
Heaters and heat pumps
Gas heaters need a properly sized gas line and clearances around the unit, and both heaters and heat pumps need the right circuit. We check those first, then plan the install around what your home already has.
Salt chlorine systems
We install the cell and control box, wire it to the pump so it only makes chlorine when water is moving, and set your starting salt level.
Automation and timers
Controls that run your pump, lights and heater on a schedule, so the equipment works the hours you choose without you walking out to the pad.
Safety fittings
Where the job touches suction lines, we make sure drain covers and suction fittings meet current anti-entrapment standards.
Signs It Is Time for New Equipment
- A loud or overheating pump
- Grinding, screeching or a motor too hot to touch usually points to worn bearings. Once that starts, replacement is often the better value.
- A cracked filter tank
- Plastic tanks and housings get brittle after years of desert sun. A hairline crack can split under pressure, so it is worth replacing before it fails.
- Breakers that keep tripping
- This can mean a failing motor or wiring that was never done right. Either way, it is a safety issue we want to look at closely.
- Repair bills on old equipment
- If you have repaired the same heater or pump more than once, we will give you an honest repair-or-replace answer. If fixing makes more sense, our Pool Repair service can handle it.
- High power bills in summer
- An old single-speed pump running long hours through a Chandler summer adds up. A properly programmed variable-speed pump usually runs far more efficiently.
How an Install Day Goes
- 1
Look at your equipment pad
We check your pool size, plumbing, breaker panel and bonding before quoting. You get a written quote that lists the equipment, the labor and whether the job needs a city inspection.
- 2
Handle the permit when needed
Jobs that add a new circuit or gas line usually need city sign-off. We file the paperwork and explain what the inspection covers.
- 3
Install and connect
We shut off power, remove the old unit, plumb in the new one, and connect the bonding and wiring to code. We protect the surrounding area and haul away the old equipment.
- 4
Start up and walk through
We prime the system, check for drips and pressure, set run schedules, and show you the controls. If an inspection is scheduled, we tell you what to expect that day.
What Affects the Price
The equipment itself is only part of the cost. What happens around it at your pad, and what the code requires for your setup, moves the total just as much. We put every piece in a line-item quote so you can see where the money goes.
- Type and size of equipment
- A heat pump costs more than a cartridge filter, and larger pools need larger units. We size for your pool, not the biggest model available.
- Plumbing changes
- New equipment often has different port sizes or heights. Some installs drop right in; others need new pipe and fittings.
- Electrical and gas work
- Adding a circuit, upgrading protection or running a gas line adds labor and usually an inspection.
- Permit and inspection
- When the city requires one, its fee and the inspection visit are part of the job. We tell you up front if your install needs it.
- Condition of the pad
- Corroded bonding wire, a cracked pad or outdated wiring may need fixing so the new equipment is installed safely.
Equipment Installation Questions
- Do I need a permit to replace my pool pump?
- A straight swap on the existing circuit often does not, but adding a new circuit, a gas heater or a salt system tied into new wiring usually does. Rules depend on the exact work, so we confirm before we start. If the city needs to sign off, we handle the paperwork and include it in your quote.
- How do you make sure the electrical side is safe?
- Before anything is connected, we check the breaker size, the ground-fault protection and the bonding wire at your pad. Water and electricity are the part of an install where shortcuts cause real problems, so we fix anything outdated rather than wiring around it. You will see any extra work listed in the quote before we do it.
- What warranty comes with the work?
- Repairs follow manufacturer warranties, between 1-2 years. We explain the coverage on your specific equipment before the job, so you know what is protected and for how long.
- How long will my pool be down?
- Most single-equipment installs are finished in a day, and your pool is running again before we leave. Jobs with new gas lines or new circuits may need an inspection visit afterward, which we schedule with you.
- Can you install equipment I bought myself?
- Often, yes. We first check that it is the right size and type for your pool and that it can be connected to code. If it will not work well with your system, we tell you before installing anything.
Ready for Equipment That Runs Right
Tell us what is failing and what pool you have, and we will lay out the options, the code steps and the cost. Many customers pair a new install with our Weekly Pool Cleaning, which comes with a free first month.